Tools, Material & Hardware

How to use a Brush/Roller for Painting









PAINTBRUSH

When you embark on an interior painting job, you'll soon discover how easy it is to use brushes competently. Even so, there are a few techniques that will help postpone fatigue and provide a neater job.

Grasp sash and trim brushes as you would a pencil (top). Hold a wall brush with your entire hand (bottom).The grip you use depends on the brush you've chosen. Trim and sash brushes with pencil handles are grasped much as you would a pencil, with the thumb and the first two fingers of the hand. This technique gives you excellent control for intricate painting. With beaver-tail handles on larger brushes, you'll need a stronger grip because the brushes are wider and heavier. Hold the handle with the entire hand, letting the handle span the width of your palm as you would hold a tennis racket. This technique works best when you're painting large, flat surfaces.

The goal of loading a brush is to get as much paint on the wall as possible without dribbling it all over the floor and yourself in the process. It will take you only a few minutes to be able to gauge accurately how much paint your brush will hold along the way. Meanwhile, start the job by dampening the bristles of the brush (with water for latex or the appropriate thinner for other types of paint) to condition them and make them more efficient. Remove excess moisture by gently striking the metal band around the handle's base against the edge of your palm and into a sink or bucket.

Never dip a brush more than about one-third the length of the bristles into the paint. If you do, the brush will become next to impossible to clean.With the first dip, move the brush around a bit in the paint to open the bristles and let the brush fill completely. It will be easier to pick up a full load if you jab the brush gently into the paint with each dip. With most latex paints, you can simply dip the brush and let the excess drip off for a few seconds before moving the brush to the wall. With thinner coatings, however, you may have to gently slap the brush against the inside of the paint can or lightly drag it across the inside edge of the lip to remove excess paint.

To neatly paint up to a line where two edges or colors meet, called "cutting in," use a trim brush with beveled bristles (the end of the brush resembles a chisel). Paint five or six strokes perpendicular to the edge of the ceiling or the wall. Next, smooth over these strokes with a single, long stroke, painting out from the corner first, then vertically. Where the wall and ceiling come together, use downward strokes on the wall first followed by smooth horizontal strokes. On the ceiling itself, cut in strokes toward the center of the room, away from the wall. Then paint a smooth horizontal stroke on the ceiling that follows the direction of the wall. Even if you're using the same color of paint on adjoining surfaces, follow this method of cutting in with 2-inch-wide borders rather than just plopping a loaded brush directly into a corner. This will prevent drips, sags, and runs.

To cut in at a corner, paint out from the corner for five or six strokes, then smooth over them with a single, long, smooth stroke.Another cutting-in approach, beading, can practically eliminate the need to use masking tape to protect one painted area from another. Use a beveled trim brush with nice long bristles. Hold the brush so that your thumb is on one side of the metal ferrule and your fingers on the other. Press the brush lightly against the surface, then, as you move the brush, add just enough pressure to make the bristles bend away from the direction of your brushstroke. Keep the brush about 1?16 inch away from the other colored surface. The bent bristles and the pressure will release a fine bead of paint that will spread into the gap.

With both methods of cutting in, but especially when you're dealing with two colors, it's better to have a brush that's too dry than one that's too wet. This is detail work. To do it effectively, go slowly and cut in 4 or 5 inches at a time. It will seem tedious at first, but your speed and accuracy.

Type of Brushes

For the best results always use good quality brushes. The quality of the brush used has a direct effect upon the quality of the finished job and the ease with which the paint is controlled and applied. A good brush is carefully shaped towards a taper or wedge shape and has a good length of bristle.

For smaller areas like coving 1-2 inch brushes are more practical. When painting doors with solvent-based paint use 2-3 inch brushes. Use a 2-3 inch brush for 'cutting in' around the tops of walls, edges of ceilings, skirtings etc. Use a 0.5-1 inch brush or special angled brush for 'cutting in' windows.

ROLLER

Rollers are ideal for painting large areas, particularly ceilings. They are quick and easy to use. There are several types of roller available to suit different paint jobs: foam, mohair or sheepskin in short, medium and long-pile. Your choice of roller really depends upon the sort of paint you are using.

A short-pile mohair roller is suitable for applying silk emulsion. A medium-pile sheepskin roller is ideal for applying matt emulsion. Foam rollers are not recommended for normal emulsion paints as their spongy texture creates air bubbles in the paint film which then burst, leaving a crated, orange peel effect.

CLEAN ROLLERS/BRUSHES

To extend the life of your brushes and rollers, it is essential to clean them thoroughly and allow them to dry before storing. How you clean brushes depends upon the type of paint you have been using.

All brushes and rollers that have been used with water-based paints should be rinsed in cold water and then washed in warm water with a little detergent. Brushes which have been used to apply solvent-based paints should be cleaned with Dulux Thinner and then washed in warm water with a little detergent.

Rinse brushes in clean water, shake off excess water and wrap in a piece of clean paper towel and secure with masking tape. The brush will then dry back to its original shape, ready for the next job. Brushes should be stored flat. Standing brushes on their ends will bend the bristles and spoil them. Rollers should be stored hanging up to avoid crushing the pile.